WILDCARD TECHNOLOGIES, INC. SATISFAXTION MOBILE PDMCIA9023COMBO Card Type Modem (asynchronous), Ethernet Chipset Intel 82595TX Maximum Onboard Memory 160KB DRAM/128KB PROM Network Transfer Rate 10Mbps Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus PCMCIA Type II Fax Class Class I & II Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation Unidentified Error Correction/Compression MNP5, MNP10, V.42, V.42bis Topology Star Wire Type Unshielded twisted pair Boot ROM Not available 52771 SUPPORTED STANDARD COMMANDS Basic AT Commands +++, A/ A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \G, \J, \K, \L, \N %C, %L, %Q Special AT Commands -K, -Q, *H, )M, @M, :E, +MS S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95, S201 Proprietary AT Command Set AUTO-RETRAIN AND AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled. %E1 Auto-retrain enabled. %E2 Auto-fallback/fall-forward enabled. %E3 Auto-retrain and fast disconnect enabled. AUTOSYNC Format AT [cmds] S19=n [cmds] Default: 0 Range: 0 - 63 Unit: Bit-mapped Description: Sets options for Hayes AutoSync functions. Bit Value Function 0 0 Not used. 1 0 BSC enabled. 1 HDLC enabled. 2 0 HDLC address detection disabled. 1 HDLC address detection enabled. 3 0 NRZI bit encoding enabled. 1 NRZ bit encoding enabled. 4 0 Mark idle enabled. 1 Flag or sync idle enabled. AUTOSYNC HDLC ADDRESS Type: Register Format: AT [cmds] S20=n [cmds] Default: 0 Range: 0-255 Unit: Unidentified Description: Sets the HDLC address or BSC character. COUNTRY CODE Type: Configuration Format: AT [cmds] *NCnn [cmds] Description: Changes the country code of the modem to nn. DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DJ MNP10 link will be negotiated at 1200bps for this call. DK MNP10 power level adjustment enabled for this call. DL Re-dial last number. DP Pulse dialing enabled. DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n. DT Tone dialing enabled. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D"WXY" Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D$ Wait for prompt tone detection function enabled. Modem waits for prompt tone for amount of time specified by the S7 command. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. D^ Calling tone toggled from current setting for this call. PULSE DIAL CODE Type: Configuration Format: AT [cmds] *Zn [cmds] Description: Sets the currently active pulse dialing code. Command Function *Z0 Use dial code 0. *Z1 Use dial code 1. DISPLAY STORED NUMBERS Type: Immediate Format: AT [cmds] \F [cmds] Description: Displays all stored phone numbers. FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options. Command Function &K0 Flow control disabled. &K3 RTS/CTS flow control enabled. &K4 XON/XOFF flow control enabled. &K5 Transparent XON/XOFF flow control enabled. &K6 RTS/CTS and XON/XOFF flow control enabled. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem model and speed I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports firmware revision. I5 Reports country code. REQUEST LIST OF FORBIDDEN NUMBERS Type: Immediate Format: AT [cmds] *B [cmds] Description: Requests the list of forbidden numbers from the modem. REQUEST LIST OF DELAYED NUMBERS Type: Immediate Format: AT [cmds] *D [cmds] Description: Requests the list of delayed numbers from the modem.